Abstract :
Compressive strength and Modulus Concrete elasticity is the main parameter for
determining concrete quality. Compressive Strength is the ability of the concrete to hold
the load it carries. A common measure of the elastic nature of a material is the modulus
of elasticity which is the ratio of the pressure applied to the change in the form of the
union of length, as a result of the pressure exerted.
This study uses an experimental method with a total of 95 test specimens. 39 Samples for
compressive strength without fly ash, 48 samples for compressive strength with fly ash
and 8 samples for modulus elasticity. The test object used was a concrete of 10 cm and a
height of 20 cm for compressive strength testing and a diameter of 15 with a height of 30
cm for testing the elastic modulus of concrete. With fly ash and variation of the NN-sika
cyclic superplasticizer are 0%,0.2%,0.4%, and 0,59%. The planned concrete quality is
Fc = 50 Mpa. The concrete press test was carried out at 3,7,14, and 28 days and the
elastic modulus test was carried out at 28 days.
In this study also conducted a series of similar tests using materials at PT. Concrete
Pioneer such as laboratory tests, calculation of the mixture with a predetermined
percentage to the testing of compressive strength and modulus of concrete elasticity. By
adopting material compositions from Mehta literature “Mix Proportions of High-
Strength Concrete Used in Four Different Metropolitan Areas of North Americaâ€. And
adopted the superplasticizer composition from the literature of PT.Sika Indonesia.
The use of 20% superplasticizer in concrete without fly ash has a higher average
compressive strength at 14 days, wich is 37.35 Mpa with a value of fcr’ of 38.8 Mpa
compared to the use of superplasticizer 0%, 0.4%, 0.59%. The use 0.2% superplasticizer
on concrete with fly ash, has a higher average compressive strength at 28 days of 42.9
Mpa with an fcr’ value of 55.5 Mpa compared with the use of a 0%, 0.4%, superplasticizer
0.59%. The use of 0.59% superplasticizer has a greater modulus of elasticity of 17213.06
Mpa calculated using the recommendation formula from ASTM-C 469 compared to the
use of superplasticizer 0%, 0.2%, 0.4%. The use of 0.4% superplasticizer has a greater
modulus of elasticity when calculated using the formula container in SNI 2847:2013
compared to the use of superplasticizer 0%, 0.2%, and 0.59%.
Keyword: NN-sika Sikamen superplasticizer, Compressive Strength, Modulus of
Elasticity. Kuat Tekan dan Modulus Elastisitas beton merupakan parameter utama untuk
menentukan mutu beton. Kuat Tekan merupakan kemampuan beton tersebut dalam
menahan beban yang dipikulnya. Tolak ukur yang umum dari sifat elastic suatu bahan
adalah modulus elastisitas yang merupakan perbandingan dari tekanan yang diberikan
dengan perubahan bentuk persatuan Panjang, sebagai akibat dari tekanan yang
diberikan.
Penelitian ini menggunakan metode eksperimen dengan total benda uji 95 sampel. 39
sampel untuk kuat tekan tanpa fly ash, 48 sampel untuk kuat tekan dengan fly ash dan 8
sampel untuk modulus elastisitas. Benda uji yang digunakan adalah silinder beton
dengan diameter 10 cm dan tinggi 20 cm untuk pengujian kuat tekan dan diameter 15
dengan tinggi 30 cm untuk pengujian modulus elastisitas beton. Dengan fly ash dan
variasi superplasticizer sikamen NN-sika adalah 0%, 0.2%, 0.4%, dan 0.59%. Mutu
beton yang direncanakan adalah Fc = 50 MPa. Uji tekan beton dilakukan pada umur 3,
7, 14, dan 28 hari dan uji modulus elastisitas dilakukan pada umur 28 hari.
Dalam penelitian ini juga dilakukan serangkaian pengujian serupa dengan menggunakan
material di PT. Pionir Beton seperti pemeriksaan laboratorium, perhitungan komposisi
campuran dengan prosentase yang telah ditentukan hingga pengujian Kuat Tekan dan
Modulus Elastisitas beton. Dengan mengadopsi komposisi material dari literatur Mehta
“Mix Proportions of High-Strength Concrete Used in Four Different Metropolitan Areas
of North Americaâ€. Dan mengadopsi komposisi superplasticizer dari literatur PT. Sika
Indonesia.
Penggunaan superplasticizer 0,2% pada beton tanpa fly ash memiliki kuat tekan ratarata
lebih tinggi pada umur 14 hari yaitu 37,35 Mpa dengan nilai fcr’ sebesar 38,8 Mpa
dibandingkan dengan penggunaan superplasticizer 0%, 0,4%, 0,59%. Penggunaan
superplasticizer 0,2% pada beton dengan fly ash, memiliki kuat tekan rata-rata lebih
tinggi pada umur 28 hari yaitu 42,9 Mpa dengan nilai fcr’ sebesar 55,5 Mpa
dibandingkan dengan penggunaan superplasticizer 0%, 0,4%, 0,59%. Penggunaan
superplasticizer 0,59% memiliki nilai modulus elastisitas lebih besar yaitu 17213,06 Mpa
dihitung menggunakan rekomendasi rumus dari ASTM-C 469 dibandingkan dengan
penggunaan superplasticizer 0%, 0,2%, 0,4%. Penggunaan superplasticizer 0,4%
memiliki nilai modulus elastisitas lebih besar apabila dihitung menggunakan rumus yang
terdapat pada SNI 2847:2013 dibandingkan dengan penggunaan s